VPL-A1002C-CJ12AS Servo Motor, Low Inertia | Allen Bradley

Type number: VPL-A1002C-CJ12AS, Part No.: VPLA1002CCJ12AS, from manufacturer: Allen Bradley, Catagory: Kinetix VP Servo Motors Drives & Motors, VPL Low Inertia Motors

della101@163.com

Products Categories
Product Description
Module No. VPL-A1002C-CJ12AS
Product name 240V AC, 100mm Bolt Circle Frame Size, 2 (Two) Magnet Stacks, 2500 RPM Rated Speed, Single-turn Encoder, Keyed Shaft, …
Product description VPL-A1002C-CJ12AS Servo Motor, Low Inertia | Allen Bradley
Part number VPLA1002CCJ12AS
Allen Bradley recommendation product VPL-A1002C-CJ14AA KINETIX; PERMANENT MAGNET ROTARY MOTOR, Servo Motor | Allen Bradley
Voltage 230 VAC, 240 VAC, 480 VAC
Manufacturer Allen Bradley
Country of origin United States
Warranty 1-2 year
Shipping Method 1.Ship worldwide, usually 5-7 days.
2. We use DHL, FedEx, UPS,TNT
Remark If you need a specific firmware or series relating to VPL-A1002C-CJ12AS, please call or email us, we probably have it in our large inventory.
Product Catalogue

VPL-A1002C-CJ12AS Servo Motor, Low Inertia | Allen Bradley

Follow these steps to rotate a connector to a new position.

1.Mount and fully seat a mating cable on the motor connector.

This provides a larger area to grasp and extends the leverage force.

2.Grasp the mated connector and cable plug with your hands and slowly rotate the motor connector into the new position. 3.Remove the cable plug after the connector is aligned.

 

Install the Motor

Perform these steps to install the motor.

 

  ATTENTION:Damage can ocur to the motor bearings and the feedback device if sharp impactis applied to the shaft during installation of couplings and pulleys. Damage to the feedbadk device can result from applying leverage to the motor mounting face when removing devices mounted on the motor shaft.

Do not strike the shaft,couplings,or pulleys with tools during installation or removal.Use a wheel puller,to apply pressure from the user end of the shaft,when attempting to remove any device from the motor shaft.

1.Leave enough space around the motor so it can disipate heat and stay within its specified operating temperature range.

See Environmental Specifications on page 22 for the operating temperature range.Do not enclose the motor unless forced air is blown

across the motor for cooling.A fan that blows air across the motor improves its performance.Keep other heat producing devices away from the motor.

2.See     Load Force Ratings on page 11 to determine the radial and axial shaft load limitations of your motor.

3.Install the motor with the connector positioned beneath the motor housing.

This position can provide better environmental protection for the connector.

 

BURN  HAZARD: Outer  surfaces  of the  motor  can  reach  a  high  temperature,125℃(257°F),during  motor  operation.

Take precautions to prevent acaidental contact with hot surfaces.Consider motor surface temperature when selecting motor mating connections and cables.

 

4.Mount  and  align  the  motor.

5.Atach the single moror cable that transmits the power,feedback,and brake signals as descrtbed below.

a.Carefully align the cable connector with the motor connector.

The flat surface on the top of the motor connector and the flat surfaces on the cable connector must align for the cable connector to mate with the motor connector.

 

  ATTENTION: Keyed connectors must be properly aligned and hand-tightened.

Do not use tools,or apply excesive force,when mating the cable to the motor connector.If the connectors do not go together with light hand force, realign and try again.

b.Hand-tighten the knurled collar one-quarter turn to fully seat the cable connector.
  ATTENTION: The overall shield on the single motor cable must be grounded to obtain an effective encoder signal.

Theencoder    data    signalis    transmitted    through    an    impedance-matthed    twisted   wie   pai   that   requies    eftective    shielding    for    opimum    performance.

Be sure thereis an effective connection between the single motor cable shield and the drive system ground.

c.Form a drip loop in the cable to carry liquids away from the connectors.

Related Products
Scroll to Top

Get A Free Quote Now !

Contact Form Demo (#3)